TCP/IP - Color Bricklet 2.0

This is the description of the TCP/IP protocol for the Color Bricklet 2.0. General information and technical specifications for the Color Bricklet 2.0 are summarized in its hardware description.

API

A general description of the TCP/IP protocol structure can be found here.

Basic Functions

BrickletColorV2.get_color
Function ID:
  • 1
Request:
  • empty payload
Response:
  • r – Type: uint16, Range: [0 to 216 - 1]
  • g – Type: uint16, Range: [0 to 216 - 1]
  • b – Type: uint16, Range: [0 to 216 - 1]
  • c – Type: uint16, Range: [0 to 216 - 1]

Returns the measured color of the sensor. The values have a range of 0 to 65535.

The red (r), green (g), blue (b) and clear (c) colors are measured with four different photodiodes that are responsive at different wavelengths:

Chart Responsivity / Wavelength

If you want to get the color periodically, it is recommended to use the CALLBACK_COLOR callback and set the period with set_color_callback_configuration.

BrickletColorV2.get_illuminance
Function ID:
  • 5
Request:
  • empty payload
Response:
  • illuminance – Type: uint32, Range: [0 to 232 - 1]

Returns the illuminance affected by the gain and integration time as set by set_configuration. To get the illuminance in Lux apply this formula:

lux = illuminance * 700 / gain / integration_time

To get a correct illuminance measurement make sure that the color values themselves are not saturated. The color value (R, G or B) is saturated if it is equal to the maximum value of 65535. In that case you have to reduce the gain, see set_configuration.

If you want to get the value periodically, it is recommended to use the CALLBACK_ILLUMINANCE callback. You can set the callback configuration with set_illuminance_callback_configuration.

BrickletColorV2.get_color_temperature
Function ID:
  • 9
Request:
  • empty payload
Response:
  • color_temperature – Type: uint16, Range: [0 to 216 - 1]

Returns the color temperature in Kelvin.

To get a correct color temperature measurement make sure that the color values themselves are not saturated. The color value (R, G or B) is saturated if it is equal to the maximum value of 65535. In that case you have to reduce the gain, see set_configuration.

If you want to get the value periodically, it is recommended to use the CALLBACK_COLOR_TEMPERATURE callback. You can set the callback configuration with set_color_temperature_callback_configuration.

BrickletColorV2.set_light
Function ID:
  • 13
Request:
  • enable – Type: bool
Response:
  • no response

Turns the white LED on the Bricklet on/off.

BrickletColorV2.get_light
Function ID:
  • 14
Request:
  • empty payload
Response:
  • enable – Type: bool

Returns the value as set by set_light.

BrickletColorV2.set_configuration
Function ID:
  • 15
Request:
  • gain – Type: uint8, Range: See meanings
  • integration_time – Type: uint8, Range: See meanings
Response:
  • no response

Sets the configuration of the sensor. Gain and integration time can be configured this way.

For configuring the gain:

  • 0: 1x Gain
  • 1: 4x Gain
  • 2: 16x Gain
  • 3: 60x Gain

For configuring the integration time:

  • 0: 2.4ms
  • 1: 24ms
  • 2: 101ms
  • 3: 154ms
  • 4: 700ms

Increasing the gain enables the sensor to detect a color from a higher distance.

The integration time provides a trade-off between conversion time and accuracy. With a longer integration time the values read will be more accurate but it will take longer to get the conversion results.

The default values are 60x gain and 154ms integration time.

The following meanings are defined for the elements of this function:

For gain:

  • 0 = 1x
  • 1 = 4x
  • 2 = 16x
  • 3 = 60x

For integration_time:

  • 0 = 2ms
  • 1 = 24ms
  • 2 = 101ms
  • 3 = 154ms
  • 4 = 700ms
BrickletColorV2.get_configuration
Function ID:
  • 16
Request:
  • empty payload
Response:
  • gain – Type: uint8, Range: See meanings
  • integration_time – Type: uint8, Range: See meanings

Returns the configuration as set by set_configuration.

The following meanings are defined for the elements of this function:

For gain:

  • 0 = 1x
  • 1 = 4x
  • 2 = 16x
  • 3 = 60x

For integration_time:

  • 0 = 2ms
  • 1 = 24ms
  • 2 = 101ms
  • 3 = 154ms
  • 4 = 700ms

Advanced Functions

BrickletColorV2.get_spitfp_error_count
Function ID:
  • 234
Request:
  • empty payload
Response:
  • error_count_ack_checksum – Type: uint32, Range: [0 to 232 - 1]
  • error_count_message_checksum – Type: uint32, Range: [0 to 232 - 1]
  • error_count_frame – Type: uint32, Range: [0 to 232 - 1]
  • error_count_overflow – Type: uint32, Range: [0 to 232 - 1]

Returns the error count for the communication between Brick and Bricklet.

The errors are divided into

  • ACK checksum errors,
  • message checksum errors,
  • framing errors and
  • overflow errors.

The errors counts are for errors that occur on the Bricklet side. All Bricks have a similar function that returns the errors on the Brick side.

BrickletColorV2.set_bootloader_mode
Function ID:
  • 235
Request:
  • mode – Type: uint8, Range: See meanings
Response:
  • status – Type: uint8, Range: See meanings

Sets the bootloader mode and returns the status after the requested mode change was instigated.

You can change from bootloader mode to firmware mode and vice versa. A change from bootloader mode to firmware mode will only take place if the entry function, device identifier and CRC are present and correct.

This function is used by Brick Viewer during flashing. It should not be necessary to call it in a normal user program.

The following meanings are defined for the elements of this function:

For mode:

  • 0 = Bootloader
  • 1 = Firmware
  • 2 = Bootloader Wait For Reboot
  • 3 = Firmware Wait For Reboot
  • 4 = Firmware Wait For Erase And Reboot

For status:

  • 0 = OK
  • 1 = Invalid Mode
  • 2 = No Change
  • 3 = Entry Function Not Present
  • 4 = Device Identifier Incorrect
  • 5 = CRC Mismatch
BrickletColorV2.get_bootloader_mode
Function ID:
  • 236
Request:
  • empty payload
Response:
  • mode – Type: uint8, Range: See meanings

Returns the current bootloader mode, see set_bootloader_mode.

The following meanings are defined for the elements of this function:

For mode:

  • 0 = Bootloader
  • 1 = Firmware
  • 2 = Bootloader Wait For Reboot
  • 3 = Firmware Wait For Reboot
  • 4 = Firmware Wait For Erase And Reboot
BrickletColorV2.set_write_firmware_pointer
Function ID:
  • 237
Request:
  • pointer – Type: uint32, Range: [0 to 232 - 1]
Response:
  • no response

Sets the firmware pointer for write_firmware. The pointer has to be increased by chunks of size 64. The data is written to flash every 4 chunks (which equals to one page of size 256).

This function is used by Brick Viewer during flashing. It should not be necessary to call it in a normal user program.

BrickletColorV2.write_firmware
Function ID:
  • 238
Request:
  • data – Type: uint8[64], Range: [0 to 255]
Response:
  • status – Type: uint8, Range: [0 to 255]

Writes 64 Bytes of firmware at the position as written by set_write_firmware_pointer before. The firmware is written to flash every 4 chunks.

You can only write firmware in bootloader mode.

This function is used by Brick Viewer during flashing. It should not be necessary to call it in a normal user program.

BrickletColorV2.set_status_led_config
Function ID:
  • 239
Request:
  • config – Type: uint8, Range: See meanings
Response:
  • no response

Sets the status LED configuration. By default the LED shows communication traffic between Brick and Bricklet, it flickers once for every 10 received data packets.

You can also turn the LED permanently on/off or show a heartbeat.

If the Bricklet is in bootloader mode, the LED is will show heartbeat by default.

The following meanings are defined for the elements of this function:

For config:

  • 0 = Off
  • 1 = On
  • 2 = Show Heartbeat
  • 3 = Show Status
BrickletColorV2.get_status_led_config
Function ID:
  • 240
Request:
  • empty payload
Response:
  • config – Type: uint8, Range: See meanings

Returns the configuration as set by set_status_led_config

The following meanings are defined for the elements of this function:

For config:

  • 0 = Off
  • 1 = On
  • 2 = Show Heartbeat
  • 3 = Show Status
BrickletColorV2.get_chip_temperature
Function ID:
  • 242
Request:
  • empty payload
Response:
  • temperature – Type: int16, Range: [-215 to 215 - 1]

Returns the temperature in °C as measured inside the microcontroller. The value returned is not the ambient temperature!

The temperature is only proportional to the real temperature and it has bad accuracy. Practically it is only useful as an indicator for temperature changes.

BrickletColorV2.reset
Function ID:
  • 243
Request:
  • empty payload
Response:
  • no response

Calling this function will reset the Bricklet. All configurations will be lost.

After a reset you have to create new device objects, calling functions on the existing ones will result in undefined behavior!

BrickletColorV2.write_uid
Function ID:
  • 248
Request:
  • uid – Type: uint32, Range: [0 to 232 - 1]
Response:
  • no response

Writes a new UID into flash. If you want to set a new UID you have to decode the Base58 encoded UID string into an integer first.

We recommend that you use Brick Viewer to change the UID.

BrickletColorV2.read_uid
Function ID:
  • 249
Request:
  • empty payload
Response:
  • uid – Type: uint32, Range: [0 to 232 - 1]

Returns the current UID as an integer. Encode as Base58 to get the usual string version.

BrickletColorV2.get_identity
Function ID:
  • 255
Request:
  • empty payload
Response:
  • uid – Type: char[8]
  • connected_uid – Type: char[8]
  • position – Type: char
  • hardware_version – Type: uint8[3], Range: [0 to 255]
  • firmware_version – Type: uint8[3], Range: [0 to 255]
  • device_identifier – Type: uint16, Range: [0 to 216 - 1]

Returns the UID, the UID where the Bricklet is connected to, the position, the hardware and firmware version as well as the device identifier.

The position can be 'a', 'b', 'c' or 'd'.

The device identifier numbers can be found here

Callback Configuration Functions

BrickletColorV2.set_color_callback_configuration
Function ID:
  • 2
Request:
  • period – Type: uint32, Unit: 1 ms, Range: [0 to 232 - 1], Default: 0
  • value_has_to_change – Type: bool, Default: false
Response:
  • no response

The period is the period with which the CALLBACK_COLOR callback is triggered periodically. A value of 0 turns the callback off.

If the value has to change-parameter is set to true, the callback is only triggered after the value has changed. If the value didn't change within the period, the callback is triggered immediately on change.

If it is set to false, the callback is continuously triggered with the period, independent of the value.

BrickletColorV2.get_color_callback_configuration
Function ID:
  • 3
Request:
  • empty payload
Response:
  • period – Type: uint32, Unit: 1 ms, Range: [0 to 232 - 1], Default: 0
  • value_has_to_change – Type: bool, Default: false

Returns the callback configuration as set by set_color_callback_configuration.

BrickletColorV2.set_illuminance_callback_configuration
Function ID:
  • 6
Request:
  • period – Type: uint32, Unit: 1 ms, Range: [0 to 232 - 1], Default: 0
  • value_has_to_change – Type: bool, Default: false
  • option – Type: char, Range: See meanings, Default: 'x'
  • min – Type: uint32, Range: [0 to 232 - 1]
  • max – Type: uint32, Range: [0 to 232 - 1]
Response:
  • no response

The period is the period with which the CALLBACK_ILLUMINANCE callback is triggered periodically. A value of 0 turns the callback off.

If the value has to change-parameter is set to true, the callback is only triggered after the value has changed. If the value didn't change within the period, the callback is triggered immediately on change.

If it is set to false, the callback is continuously triggered with the period, independent of the value.

It is furthermore possible to constrain the callback with thresholds.

The option-parameter together with min/max sets a threshold for the CALLBACK_ILLUMINANCE callback.

The following options are possible:

Option Description
'x' Threshold is turned off
'o' Threshold is triggered when the value is outside the min and max values
'i' Threshold is triggered when the value is inside or equal to the min and max values
'<' Threshold is triggered when the value is smaller than the min value (max is ignored)
'>' Threshold is triggered when the value is greater than the min value (max is ignored)

If the option is set to 'x' (threshold turned off) the callback is triggered with the fixed period.

The default value is (0, false, 'x', 0, 0).

The following meanings are defined for the elements of this function:

For option:

  • 'x' = Off
  • 'o' = Outside
  • 'i' = Inside
  • '<' = Smaller
  • '>' = Greater
BrickletColorV2.get_illuminance_callback_configuration
Function ID:
  • 7
Request:
  • empty payload
Response:
  • period – Type: uint32, Unit: 1 ms, Range: [0 to 232 - 1], Default: 0
  • value_has_to_change – Type: bool, Default: false
  • option – Type: char, Range: See meanings, Default: 'x'
  • min – Type: uint32, Range: [0 to 232 - 1]
  • max – Type: uint32, Range: [0 to 232 - 1]

Returns the callback configuration as set by set_illuminance_callback_configuration.

The following meanings are defined for the elements of this function:

For option:

  • 'x' = Off
  • 'o' = Outside
  • 'i' = Inside
  • '<' = Smaller
  • '>' = Greater
BrickletColorV2.set_color_temperature_callback_configuration
Function ID:
  • 10
Request:
  • period – Type: uint32, Unit: 1 ms, Range: [0 to 232 - 1], Default: 0
  • value_has_to_change – Type: bool, Default: false
  • option – Type: char, Range: See meanings, Default: 'x'
  • min – Type: uint16, Range: [0 to 216 - 1]
  • max – Type: uint16, Range: [0 to 216 - 1]
Response:
  • no response

The period is the period with which the CALLBACK_COLOR_TEMPERATURE callback is triggered periodically. A value of 0 turns the callback off.

If the value has to change-parameter is set to true, the callback is only triggered after the value has changed. If the value didn't change within the period, the callback is triggered immediately on change.

If it is set to false, the callback is continuously triggered with the period, independent of the value.

It is furthermore possible to constrain the callback with thresholds.

The option-parameter together with min/max sets a threshold for the CALLBACK_COLOR_TEMPERATURE callback.

The following options are possible:

Option Description
'x' Threshold is turned off
'o' Threshold is triggered when the value is outside the min and max values
'i' Threshold is triggered when the value is inside or equal to the min and max values
'<' Threshold is triggered when the value is smaller than the min value (max is ignored)
'>' Threshold is triggered when the value is greater than the min value (max is ignored)

If the option is set to 'x' (threshold turned off) the callback is triggered with the fixed period.

The default value is (0, false, 'x', 0, 0).

The following meanings are defined for the elements of this function:

For option:

  • 'x' = Off
  • 'o' = Outside
  • 'i' = Inside
  • '<' = Smaller
  • '>' = Greater
BrickletColorV2.get_color_temperature_callback_configuration
Function ID:
  • 11
Request:
  • empty payload
Response:
  • period – Type: uint32, Unit: 1 ms, Range: [0 to 232 - 1], Default: 0
  • value_has_to_change – Type: bool, Default: false
  • option – Type: char, Range: See meanings, Default: 'x'
  • min – Type: uint16, Range: [0 to 216 - 1]
  • max – Type: uint16, Range: [0 to 216 - 1]

Returns the callback configuration as set by set_color_temperature_callback_configuration.

The following meanings are defined for the elements of this function:

For option:

  • 'x' = Off
  • 'o' = Outside
  • 'i' = Inside
  • '<' = Smaller
  • '>' = Greater

Callbacks

BrickletColorV2.CALLBACK_COLOR
Function ID:
  • 4
Response:
  • r – Type: uint16, Range: [0 to 216 - 1]
  • g – Type: uint16, Range: [0 to 216 - 1]
  • b – Type: uint16, Range: [0 to 216 - 1]
  • c – Type: uint16, Range: [0 to 216 - 1]

This callback is triggered periodically with the period that is set by set_color_callback_configuration. The response value is the color of the sensor as RGBC.

The CALLBACK_COLOR callback is only triggered if the color has changed since the last triggering.

BrickletColorV2.CALLBACK_ILLUMINANCE
Function ID:
  • 8
Response:
  • illuminance – Type: uint32, Range: [0 to 232 - 1]

This callback is triggered periodically according to the configuration set by set_illuminance_callback_configuration.

The response value is the same as get_illuminance.

BrickletColorV2.CALLBACK_COLOR_TEMPERATURE
Function ID:
  • 12
Response:
  • color_temperature – Type: uint16, Range: [0 to 216 - 1]

This callback is triggered periodically according to the configuration set by set_color_temperature_callback_configuration.

The response value is the same as get_color_temperature.