JavaScript - Stepper Brick¶

Configuration (Node.js)¶

Download (ExampleConfiguration.js)

 1
 2
 3
 4
 5
 6
 7
 8
 9
10
11
12
13
14
15
16
17
18
19
20
21
22
23
24
25
26
27
28
29
30
31
32
33
34
35
36
37
38
39
40
41
42
43
44
45
46
47

var Tinkerforge = require('tinkerforge');

var HOST = 'localhost';
var PORT = 4223;
var UID = 'XXYYZZ'; // Change XXYYZZ to the UID of your Stepper Brick

var ipcon = new Tinkerforge.IPConnection(); // Create IP connection
var stepper = new Tinkerforge.BrickStepper(UID, ipcon); // Create device object

ipcon.connect(HOST, PORT,
    function (error) {
        console.log('Error: ' + error);
    }
); // Connect to brickd
// Don't use device before ipcon is connected

ipcon.on(Tinkerforge.IPConnection.CALLBACK_CONNECTED,
    function (connectReason) {
        stepper.setMotorCurrent(800); // 800 mA
        stepper.setStepMode(8); // 1/8 step mode
        stepper.setMaxVelocity(2000); // Velocity 2000 steps/s

        // Slow acceleration (500 steps/s^2),
        // Fast deacceleration (5000 steps/s^2)
        stepper.setSpeedRamping(500, 5000);

        stepper.enable(); // Enable motor power
        stepper.setSteps(60000); // Drive 60000 steps forward
    }
);

console.log('Press key to exit');
process.stdin.on('data',
    function (data) {
        // Stop motor before disabling motor power
        stepper.stop(); // Request motor stop
        stepper.setSpeedRamping(500,
                                5000); // Fast deacceleration (5000 steps/s^2) for stopping

        setTimeout(function () {
            stepper.disable(); // Disable motor power

            ipcon.disconnect();
            process.exit(0);
        }, 400); // Wait for motor to actually stop: max velocity (2000 steps/s) / decceleration (5000 steps/s^2) = 0.4 s
    }
);

Callback (Node.js)¶

Download (ExampleCallback.js)

 1
 2
 3
 4
 5
 6
 7
 8
 9
10
11
12
13
14
15
16
17
18
19
20
21
22
23
24
25
26
27
28
29
30
31
32
33
34
35
36
37
38
39
40
41
42
43
44
45
46
47
48
49
50
51
52
53
54
55
56
57
58
59
60
61
62
63

var Tinkerforge = require('tinkerforge');

var HOST = 'localhost';
var PORT = 4223;
var UID = 'XXYYZZ'; // Change XXYYZZ to the UID of your Stepper Brick

var ipcon = new Tinkerforge.IPConnection(); // Create IP connection
var stepper = new Tinkerforge.BrickStepper(UID, ipcon); // Create device object

ipcon.connect(HOST, PORT,
    function (error) {
        console.log('Error: ' + error);
    }
); // Connect to brickd
// Don't use device before ipcon is connected

ipcon.on(Tinkerforge.IPConnection.CALLBACK_CONNECTED,
    function (connectReason) {
        stepper.enable(); // Enable motor power
        stepper.setSteps(1); // Drive one step forward to get things going
    }
);

// Register position reached callback
stepper.on(Tinkerforge.BrickStepper.CALLBACK_POSITION_REACHED,
    // Use position reached callback to program random movement
    function (position) {
        if(Math.floor(Math.random()*2)) {
            var steps = Math.floor((Math.random()*5000)+1000); // steps (forward);
            console.log('Driving forward: '+steps+' steps');
        }
        else {
            var steps = Math.floor((Math.random()*(-1000))+(-5000)); // steps (backward);
            console.log('Driving backward: '+steps+' steps');
        }

        var vel = Math.floor((Math.random()*2000)+200); // steps/s
        var acc = Math.floor((Math.random()*1000)+100); // steps/s^2
        var dec = Math.floor((Math.random()*1000)+100); // steps/s^2
        console.log('Configuration (vel, acc, dec): '+vel+', '+acc+', '+dec);

        stepper.setSpeedRamping(acc, dec);
        stepper.setMaxVelocity(vel);
        stepper.setSteps(steps);
    }
);

console.log('Press key to exit');
process.stdin.on('data',
    function (data) {
        // Stop motor before disabling motor power
        stepper.stop(); // Request motor stop
        stepper.setSpeedRamping(500,
                                5000); // Fast deacceleration (5000 steps/s^2) for stopping

        setTimeout(function () {
            stepper.disable(); // Disable motor power

            ipcon.disconnect();
            process.exit(0);
        }, 400); // Wait for motor to actually stop: max velocity (2000 steps/s) / decceleration (5000 steps/s^2) = 0.4 s
    }
);

Configuration (HTML)¶

Download (ExampleConfiguration.html), Test (ExampleConfiguration.html)

 1
 2
 3
 4
 5
 6
 7
 8
 9
10
11
12
13
14
15
16
17
18
19
20
21
22
23
24
25
26
27
28
29
30
31
32
33
34
35
36
37
38
39
40
41
42
43
44
45
46
47
48
49
50
51
52
53
54
55
56
57
58
59

<!DOCTYPE html>
<html>
    <meta http-equiv="Content-Type" content="text/html; charset=utf-8" />
    <head>
        <title>Tinkerforge | JavaScript Example</title>
    </head>
    <body>
        <div style="text-align:center;">
            <h1>Stepper Brick Configuration Example</h1>
            <p>
                <input value="localhost" id="host" type="text" size="20">:
                <input value="4280" id="port" type="text" size="5">,
                <input value="uid" id="uid" type="text" size="5">
                <input value="Start Example" id="start" type="button" onclick="startExample();">
            </p>
            <p>
                <textarea readonly id="text" cols="80" rows="24" style="resize:none;"
                          >Press "Start Example" to begin ...</textarea>
            </p>
        </div>
        <script src="./Tinkerforge.js" type='text/javascript'></script>
        <script type='text/javascript'>
            var ipcon;
            var textArea = document.getElementById("text");
            function startExample() {
                textArea.value = "";
                var HOST = document.getElementById("host").value;
                var PORT = parseInt(document.getElementById("port").value);
                var UID = document.getElementById("uid").value;
                if(ipcon !== undefined) {
                    ipcon.disconnect();
                }
                ipcon = new Tinkerforge.IPConnection(); // Create IP connection
                var stepper = new Tinkerforge.BrickStepper(UID, ipcon); // Create device object
                ipcon.connect(HOST, PORT,
                    function(error) {
                        textArea.value += 'Error: ' + error + '\n';
                    }
                ); // Connect to brickd
                // Don't use device before ipcon is connected

                ipcon.on(Tinkerforge.IPConnection.CALLBACK_CONNECTED,
                    function (connectReason) {
                        stepper.setMotorCurrent(800); // 800 mA
                        stepper.setStepMode(8); // 1/8 step mode
                        stepper.setMaxVelocity(2000); // Velocity 2000 steps/s

                        // Slow acceleration (500 steps/s^2),
                        // Fast deacceleration (5000 steps/s^2)
                        stepper.setSpeedRamping(500, 5000);

                        stepper.enable(); // Enable motor power
                        stepper.setSteps(60000); // Drive 60000 steps forward
                    }
                );
            }
        </script>
    </body>
</html>

Callback (HTML)¶

Download (ExampleCallback.html), Test (ExampleCallback.html)

 1
 2
 3
 4
 5
 6
 7
 8
 9
10
11
12
13
14
15
16
17
18
19
20
21
22
23
24
25
26
27
28
29
30
31
32
33
34
35
36
37
38
39
40
41
42
43
44
45
46
47
48
49
50
51
52
53
54
55
56
57
58
59
60
61
62
63
64
65
66
67
68
69
70
71
72
73
74

<!DOCTYPE html>
<html>
    <meta http-equiv="Content-Type" content="text/html; charset=utf-8" />
    <head>
        <title>Tinkerforge | JavaScript Example</title>
    </head>
    <body>
        <div style="text-align:center;">
            <h1>Stepper Brick Callback Example</h1>
            <p>
                <input value="localhost" id="host" type="text" size="20">:
                <input value="4280" id="port" type="text" size="5">,
                <input value="uid" id="uid" type="text" size="5">
                <input value="Start Example" id="start" type="button" onclick="startExample();">
            </p>
            <p>
                <textarea readonly id="text" cols="80" rows="24" style="resize:none;"
                          >Press "Start Example" to begin ...</textarea>
            </p>
        </div>
        <script src="./Tinkerforge.js" type='text/javascript'></script>
        <script type='text/javascript'>
            var ipcon;
            var textArea = document.getElementById("text");
            function startExample() {
                textArea.value = "";
                var HOST = document.getElementById("host").value;
                var PORT = parseInt(document.getElementById("port").value);
                var UID = document.getElementById("uid").value;
                if(ipcon !== undefined) {
                    ipcon.disconnect();
                }
                ipcon = new Tinkerforge.IPConnection(); // Create IP connection
                var stepper = new Tinkerforge.BrickStepper(UID, ipcon); // Create device object
                ipcon.connect(HOST, PORT,
                    function(error) {
                        textArea.value += 'Error: ' + error + '\n';
                    }
                ); // Connect to brickd
                // Don't use device before ipcon is connected

                ipcon.on(Tinkerforge.IPConnection.CALLBACK_CONNECTED,
                    function (connectReason) {
                        stepper.enable(); // Enable motor power
                        stepper.setSteps(1); // Drive one step forward to get things going
                    }
                );

                // Register position reached callback
                stepper.on(Tinkerforge.BrickStepper.CALLBACK_POSITION_REACHED,
                    // Use position reached callback to program random movement
                    function (position) {
                        if(Math.floor(Math.random()*2)) {
                            var steps = Math.floor((Math.random()*5000)+1000); // steps (forward);
                            textArea.value += 'Driving forward: '+steps+' steps\n';
                        }
                        else {
                            var steps = Math.floor((Math.random()*(-1000))+(-5000)); // steps (backward);
                            textArea.value += 'Driving backward: '+steps+' steps\n';
                        }
                        var vel = Math.floor((Math.random()*2000)+200); // steps/s
                        var acc = Math.floor((Math.random()*1000)+100); // steps/s^2
                        var dec = Math.floor((Math.random()*1000)+100); // steps/s^2
                        textArea.value += 'Configuration (vel, acc, dec): '+vel+', '+acc+', '+dec+'\n';
                        stepper.setSpeedRamping(acc, dec);
                        stepper.setMaxVelocity(vel);
                        stepper.setSteps(steps);
                        textArea.scrollTop = textArea.scrollHeight;
                    }
                );
            }
        </script>
    </body>
</html>

Basic Functions¶

new BrickStepper(uid, ipcon)¶

Parameters:	uid – Type: string ipcon – Type: IPConnection
Returns:	stepper – Type: BrickStepper

Creates an object with the unique device ID uid:

var stepper = new BrickStepper("YOUR_DEVICE_UID", ipcon);

This object can then be used after the IP Connection is connected.

BrickStepper.setMaxVelocity(velocity[, returnCallback][, errorCallback])¶

Parameters:	velocity – Type: int, Unit: 1 1/s, Range: [0 to 216 - 1]
Callback Parameters:	undefined
Returns:	undefined

Sets the maximum velocity of the stepper motor. This function does not start the motor, it merely sets the maximum velocity the stepper motor is accelerated to. To get the motor running use either setTargetPosition(), setSteps(), driveForward() or driveBackward().

BrickStepper.getMaxVelocity([returnCallback][, errorCallback])¶

Callback Parameters:	velocity – Type: int, Unit: 1 1/s, Range: [0 to 216 - 1]
Returns:	undefined

Returns the velocity as set by setMaxVelocity().

BrickStepper.getCurrentVelocity([returnCallback][, errorCallback])¶

Callback Parameters:	velocity – Type: int, Unit: 1 1/s, Range: [0 to 216 - 1]
Returns:	undefined

Returns the current velocity of the stepper motor.

BrickStepper.setSpeedRamping(acceleration, deacceleration[, returnCallback][, errorCallback])¶

Parameters:	acceleration – Type: int, Unit: 1 1/s², Range: [0 to 216 - 1], Default: 1000 deacceleration – Type: int, Unit: 1 1/s², Range: [0 to 216 - 1], Default: 1000
Callback Parameters:	undefined
Returns:	undefined

Sets the acceleration and deacceleration of the stepper motor. An acceleration of 1000 means, that every second the velocity is increased by 1000 steps/s.

For example: If the current velocity is 0 and you want to accelerate to a velocity of 8000 steps/s in 10 seconds, you should set an acceleration of 800 steps/s².

An acceleration/deacceleration of 0 means instantaneous acceleration/deacceleration (not recommended)

BrickStepper.getSpeedRamping([returnCallback][, errorCallback])¶

Callback Parameters:	acceleration – Type: int, Unit: 1 1/s², Range: [0 to 216 - 1], Default: 1000 deacceleration – Type: int, Unit: 1 1/s², Range: [0 to 216 - 1], Default: 1000
Returns:	undefined

Returns the acceleration and deacceleration as set by setSpeedRamping().

BrickStepper.fullBrake([returnCallback][, errorCallback])¶

Callback Parameters:	undefined
Returns:	undefined

Executes an active full brake.

Warning

This function is for emergency purposes, where an immediate brake is necessary. Depending on the current velocity and the strength of the motor, a full brake can be quite violent.

Call stop() if you just want to stop the motor.

BrickStepper.setSteps(steps[, returnCallback][, errorCallback])¶

Parameters:	steps – Type: int, Range: [-231 to 231 - 1]
Callback Parameters:	undefined
Returns:	undefined

Sets the number of steps the stepper motor should run. Positive values will drive the motor forward and negative values backward. The velocity, acceleration and deacceleration as set by setMaxVelocity() and setSpeedRamping() will be used.

BrickStepper.getSteps([returnCallback][, errorCallback])¶

Callback Parameters:	steps – Type: int, Range: [-231 to 231 - 1]
Returns:	undefined

Returns the last steps as set by setSteps().

BrickStepper.getRemainingSteps([returnCallback][, errorCallback])¶

Callback Parameters:	steps – Type: int, Range: [-231 to 231 - 1]
Returns:	undefined

Returns the remaining steps of the last call of setSteps(). For example, if setSteps() is called with 2000 and getRemainingSteps() is called after the motor has run for 500 steps, it will return 1500.

BrickStepper.driveForward([returnCallback][, errorCallback])¶

Callback Parameters:	undefined
Returns:	undefined

Drives the stepper motor forward until driveBackward() or stop() is called. The velocity, acceleration and deacceleration as set by setMaxVelocity() and setSpeedRamping() will be used.

BrickStepper.driveBackward([returnCallback][, errorCallback])¶

Callback Parameters:	undefined
Returns:	undefined

Drives the stepper motor backward until driveForward() or stop() is triggered. The velocity, acceleration and deacceleration as set by setMaxVelocity() and setSpeedRamping() will be used.

BrickStepper.stop([returnCallback][, errorCallback])¶

Callback Parameters:	undefined
Returns:	undefined

Stops the stepper motor with the deacceleration as set by setSpeedRamping().

BrickStepper.setMotorCurrent(current[, returnCallback][, errorCallback])¶

Parameters:	current – Type: int, Unit: 1 mA, Range: [100 to 2291], Default: 800
Callback Parameters:	undefined
Returns:	undefined

Sets the current with which the motor will be driven.

Warning

Do not set this value above the specifications of your stepper motor. Otherwise it may damage your motor.

BrickStepper.getMotorCurrent([returnCallback][, errorCallback])¶

Callback Parameters:	current – Type: int, Unit: 1 mA, Range: [100 to 2291], Default: 800
Returns:	undefined

Returns the current as set by setMotorCurrent().

BrickStepper.enable([returnCallback][, errorCallback])¶

Callback Parameters:	undefined
Returns:	undefined

Enables the driver chip. The driver parameters can be configured (maximum velocity, acceleration, etc) before it is enabled.

BrickStepper.disable([returnCallback][, errorCallback])¶

Callback Parameters:	undefined
Returns:	undefined

Disables the driver chip. The configurations are kept (maximum velocity, acceleration, etc) but the motor is not driven until it is enabled again.

Warning

Disabling the driver chip while the motor is still turning can damage the driver chip. The motor should be stopped calling stop() function before disabling the motor power. The stop() function will not wait until the motor is actually stopped. You have to explicitly wait for the appropriate time after calling the stop() function before calling the disable() function.

BrickStepper.isEnabled([returnCallback][, errorCallback])¶

Callback Parameters:	enabled – Type: boolean, Default: false
Returns:	undefined

Returns true if the driver chip is enabled, false otherwise.

Advanced Functions¶

BrickStepper.setCurrentPosition(position[, returnCallback][, errorCallback])¶

Parameters:	position – Type: int, Range: [-231 to 231 - 1]
Callback Parameters:	undefined
Returns:	undefined

Sets the current steps of the internal step counter. This can be used to set the current position to 0 when some kind of starting position is reached (e.g. when a CNC machine reaches a corner).

BrickStepper.getCurrentPosition([returnCallback][, errorCallback])¶

Callback Parameters:	position – Type: int, Range: [-231 to 231 - 1]
Returns:	undefined

Returns the current position of the stepper motor in steps. On startup the position is 0. The steps are counted with all possible driving functions (setTargetPosition(), setSteps(), driveForward() or driveBackward()). It also is possible to reset the steps to 0 or set them to any other desired value with setCurrentPosition().

BrickStepper.setTargetPosition(position[, returnCallback][, errorCallback])¶

Parameters:	position – Type: int, Range: [-231 to 231 - 1]
Callback Parameters:	undefined
Returns:	undefined

Sets the target position of the stepper motor in steps. For example, if the current position of the motor is 500 and setTargetPosition() is called with 1000, the stepper motor will drive 500 steps forward. It will use the velocity, acceleration and deacceleration as set by setMaxVelocity() and setSpeedRamping().

A call of setTargetPosition() with the parameter x is equivalent to a call of setSteps() with the parameter (x - getCurrentPosition()).

BrickStepper.getTargetPosition([returnCallback][, errorCallback])¶

Callback Parameters:	position – Type: int, Range: [-231 to 231 - 1]
Returns:	undefined

Returns the last target position as set by setTargetPosition().

BrickStepper.setStepMode(mode[, returnCallback][, errorCallback])¶

Parameters:	mode – Type: int, Range: See constants, Default: 8
Callback Parameters:	undefined
Returns:	undefined

Sets the step mode of the stepper motor. Possible values are:

• Full Step = 1
• Half Step = 2
• Quarter Step = 4
• Eighth Step = 8

A higher value will increase the resolution and decrease the torque of the stepper motor.

The following constants are available for this function:

For mode:

• BrickStepper.STEP_MODE_FULL_STEP = 1
• BrickStepper.STEP_MODE_HALF_STEP = 2
• BrickStepper.STEP_MODE_QUARTER_STEP = 4
• BrickStepper.STEP_MODE_EIGHTH_STEP = 8

BrickStepper.getStepMode([returnCallback][, errorCallback])¶

Callback Parameters:	mode – Type: int, Range: See constants, Default: 8
Returns:	undefined

Returns the step mode as set by setStepMode().

The following constants are available for this function:

For mode:

• BrickStepper.STEP_MODE_FULL_STEP = 1
• BrickStepper.STEP_MODE_HALF_STEP = 2
• BrickStepper.STEP_MODE_QUARTER_STEP = 4
• BrickStepper.STEP_MODE_EIGHTH_STEP = 8

BrickStepper.getStackInputVoltage([returnCallback][, errorCallback])¶

Callback Parameters:	voltage – Type: int, Unit: 1 mV, Range: [0 to 216 - 1]
Returns:	undefined

Returns the stack input voltage. The stack input voltage is the voltage that is supplied via the stack, i.e. it is given by a Step-Down or Step-Up Power Supply.

BrickStepper.getExternalInputVoltage([returnCallback][, errorCallback])¶

Callback Parameters:	voltage – Type: int, Unit: 1 mV, Range: [0 to 216 - 1]
Returns:	undefined

Returns the external input voltage. The external input voltage is given via the black power input connector on the Stepper Brick.

If there is an external input voltage and a stack input voltage, the motor will be driven by the external input voltage. If there is only a stack voltage present, the motor will be driven by this voltage.

Warning

This means, if you have a high stack voltage and a low external voltage, the motor will be driven with the low external voltage. If you then remove the external connection, it will immediately be driven by the high stack voltage

BrickStepper.getCurrentConsumption([returnCallback][, errorCallback])¶

Callback Parameters:	current – Type: int, Unit: 1 mA, Range: [0 to 216 - 1]
Returns:	undefined

Returns the current consumption of the motor.

BrickStepper.setDecay(decay[, returnCallback][, errorCallback])¶

Parameters:	decay – Type: int, Range: [0 to 216 - 1], Default: 10000
Callback Parameters:	undefined
Returns:	undefined

Sets the decay mode of the stepper motor. A value of 0 sets the fast decay mode, a value of 65535 sets the slow decay mode and a value in between sets the mixed decay mode.

Changing the decay mode is only possible if synchronous rectification is enabled (see setSyncRect()).

For a good explanation of the different decay modes see this blog post by Avayan.

A good decay mode is unfortunately different for every motor. The best way to work out a good decay mode for your stepper motor, if you can't measure the current with an oscilloscope, is to listen to the sound of the motor. If the value is too low, you often hear a high pitched sound and if it is too high you can often hear a humming sound.

Generally, fast decay mode (small value) will be noisier but also allow higher motor speeds.

Note

There is unfortunately no formula to calculate a perfect decay mode for a given stepper motor. If you have problems with loud noises or the maximum motor speed is too slow, you should try to tinker with the decay value

BrickStepper.getDecay([returnCallback][, errorCallback])¶

Callback Parameters:	decay – Type: int, Range: [0 to 216 - 1], Default: 10000
Returns:	undefined

Returns the decay mode as set by setDecay().

BrickStepper.setSyncRect(syncRect[, returnCallback][, errorCallback])¶

Parameters:	syncRect – Type: boolean, Default: false
Callback Parameters:	undefined
Returns:	undefined

Turns synchronous rectification on or off (true or false).

With synchronous rectification on, the decay can be changed (see setDecay()). Without synchronous rectification fast decay is used.

For an explanation of synchronous rectification see here.

Warning

If you want to use high speeds (> 10000 steps/s) for a large stepper motor with a large inductivity we strongly suggest that you disable synchronous rectification. Otherwise the Brick may not be able to cope with the load and overheat.

BrickStepper.isSyncRect([returnCallback][, errorCallback])¶

Callback Parameters:	syncRect – Type: boolean, Default: false
Returns:	undefined

Returns true if synchronous rectification is enabled, false otherwise.

BrickStepper.setTimeBase(timeBase[, returnCallback][, errorCallback])¶

Parameters:	timeBase – Type: int, Unit: 1 s, Range: [0 to 232 - 1], Default: 1
Callback Parameters:	undefined
Returns:	undefined

Sets the time base of the velocity and the acceleration of the stepper brick.

For example, if you want to make one step every 1.5 seconds, you can set the time base to 15 and the velocity to 10. Now the velocity is 10steps/15s = 1steps/1.5s.

BrickStepper.getTimeBase([returnCallback][, errorCallback])¶

Callback Parameters:	timeBase – Type: int, Unit: 1 s, Range: [0 to 232 - 1], Default: 1
Returns:	undefined

Returns the time base as set by setTimeBase().

BrickStepper.getAllData([returnCallback][, errorCallback])¶

Callback Parameters:	currentVelocity – Type: int, Unit: 1 1/s, Range: [0 to 216 - 1] currentPosition – Type: int, Range: [-231 to 231 - 1] remainingSteps – Type: int, Range: [-231 to 231 - 1] stackVoltage – Type: int, Unit: 1 mV, Range: [0 to 216 - 1] externalVoltage – Type: int, Unit: 1 mV, Range: [0 to 216 - 1] currentConsumption – Type: int, Unit: 1 mA, Range: [0 to 216 - 1]
Returns:	undefined

Returns the following parameters: The current velocity, the current position, the remaining steps, the stack voltage, the external voltage and the current consumption of the stepper motor.

There is also a callback for this function, see CALLBACK_ALL_DATA callback.

BrickStepper.setSPITFPBaudrateConfig(enableDynamicBaudrate, minimumDynamicBaudrate[, returnCallback][, errorCallback])¶

Parameters:	enableDynamicBaudrate – Type: boolean, Default: true minimumDynamicBaudrate – Type: int, Unit: 1 Bd, Range: [400000 to 2000000], Default: 400000
Callback Parameters:	undefined
Returns:	undefined

The SPITF protocol can be used with a dynamic baudrate. If the dynamic baudrate is enabled, the Brick will try to adapt the baudrate for the communication between Bricks and Bricklets according to the amount of data that is transferred.

The baudrate will be increased exponentially if lots of data is sent/received and decreased linearly if little data is sent/received.

This lowers the baudrate in applications where little data is transferred (e.g. a weather station) and increases the robustness. If there is lots of data to transfer (e.g. Thermal Imaging Bricklet) it automatically increases the baudrate as needed.

In cases where some data has to transferred as fast as possible every few seconds (e.g. RS485 Bricklet with a high baudrate but small payload) you may want to turn the dynamic baudrate off to get the highest possible performance.

The maximum value of the baudrate can be set per port with the function setSPITFPBaudrate(). If the dynamic baudrate is disabled, the baudrate as set by setSPITFPBaudrate() will be used statically.

New in version 2.3.6 (Firmware).

BrickStepper.getSPITFPBaudrateConfig([returnCallback][, errorCallback])¶

Callback Parameters:	enableDynamicBaudrate – Type: boolean, Default: true minimumDynamicBaudrate – Type: int, Unit: 1 Bd, Range: [400000 to 2000000], Default: 400000
Returns:	undefined

Returns the baudrate config, see setSPITFPBaudrateConfig().

New in version 2.3.6 (Firmware).

BrickStepper.getSendTimeoutCount(communicationMethod[, returnCallback][, errorCallback])¶

Parameters:	communicationMethod – Type: int, Range: See constants
Callback Parameters:	timeoutCount – Type: int, Range: [0 to 232 - 1]
Returns:	undefined

Returns the timeout count for the different communication methods.

The methods 0-2 are available for all Bricks, 3-7 only for Master Bricks.

This function is mostly used for debugging during development, in normal operation the counters should nearly always stay at 0.

The following constants are available for this function:

For communication_method:

• BrickStepper.COMMUNICATION_METHOD_NONE = 0
• BrickStepper.COMMUNICATION_METHOD_USB = 1
• BrickStepper.COMMUNICATION_METHOD_SPI_STACK = 2
• BrickStepper.COMMUNICATION_METHOD_CHIBI = 3
• BrickStepper.COMMUNICATION_METHOD_RS485 = 4
• BrickStepper.COMMUNICATION_METHOD_WIFI = 5
• BrickStepper.COMMUNICATION_METHOD_ETHERNET = 6
• BrickStepper.COMMUNICATION_METHOD_WIFI_V2 = 7

New in version 2.3.4 (Firmware).

BrickStepper.setSPITFPBaudrate(brickletPort, baudrate[, returnCallback][, errorCallback])¶

Parameters:	brickletPort – Type: char, Range: ['a' to 'b'] baudrate – Type: int, Unit: 1 Bd, Range: [400000 to 2000000], Default: 1400000
Callback Parameters:	undefined
Returns:	undefined

Sets the baudrate for a specific Bricklet port.

If you want to increase the throughput of Bricklets you can increase the baudrate. If you get a high error count because of high interference (see getSPITFPErrorCount()) you can decrease the baudrate.

If the dynamic baudrate feature is enabled, the baudrate set by this function corresponds to the maximum baudrate (see setSPITFPBaudrateConfig()).

Regulatory testing is done with the default baudrate. If CE compatibility or similar is necessary in your applications we recommend to not change the baudrate.

New in version 2.3.3 (Firmware).

BrickStepper.getSPITFPBaudrate(brickletPort[, returnCallback][, errorCallback])¶

Parameters:	brickletPort – Type: char, Range: ['a' to 'b']
Callback Parameters:	baudrate – Type: int, Unit: 1 Bd, Range: [400000 to 2000000], Default: 1400000
Returns:	undefined

Returns the baudrate for a given Bricklet port, see setSPITFPBaudrate().

New in version 2.3.3 (Firmware).

BrickStepper.getSPITFPErrorCount(brickletPort[, returnCallback][, errorCallback])¶

Parameters:	brickletPort – Type: char, Range: ['a' to 'b']
Callback Parameters:	errorCountACKChecksum – Type: int, Range: [0 to 232 - 1] errorCountMessageChecksum – Type: int, Range: [0 to 232 - 1] errorCountFrame – Type: int, Range: [0 to 232 - 1] errorCountOverflow – Type: int, Range: [0 to 232 - 1]
Returns:	undefined

Returns the error count for the communication between Brick and Bricklet.

The errors are divided into

• ACK checksum errors,
• message checksum errors,
• framing errors and
• overflow errors.

The errors counts are for errors that occur on the Brick side. All Bricklets have a similar function that returns the errors on the Bricklet side.

New in version 2.3.3 (Firmware).

BrickStepper.enableStatusLED([returnCallback][, errorCallback])¶

Callback Parameters:	undefined
Returns:	undefined

Enables the status LED.

The status LED is the blue LED next to the USB connector. If enabled is is on and it flickers if data is transfered. If disabled it is always off.

The default state is enabled.

New in version 2.3.1 (Firmware).

BrickStepper.disableStatusLED([returnCallback][, errorCallback])¶

Callback Parameters:	undefined
Returns:	undefined

Disables the status LED.

The status LED is the blue LED next to the USB connector. If enabled is is on and it flickers if data is transfered. If disabled it is always off.

The default state is enabled.

New in version 2.3.1 (Firmware).

BrickStepper.isStatusLEDEnabled([returnCallback][, errorCallback])¶

Callback Parameters:	enabled – Type: boolean, Default: true
Returns:	undefined

Returns true if the status LED is enabled, false otherwise.

New in version 2.3.1 (Firmware).

BrickStepper.getChipTemperature([returnCallback][, errorCallback])¶

Callback Parameters:	temperature – Type: int, Unit: 1/10 °C, Range: [-215 to 215 - 1]
Returns:	undefined

Returns the temperature as measured inside the microcontroller. The value returned is not the ambient temperature!

The temperature is only proportional to the real temperature and it has an accuracy of ±15%. Practically it is only useful as an indicator for temperature changes.

BrickStepper.reset([returnCallback][, errorCallback])¶

Callback Parameters:	undefined
Returns:	undefined

Calling this function will reset the Brick. Calling this function on a Brick inside of a stack will reset the whole stack.

After a reset you have to create new device objects, calling functions on the existing ones will result in undefined behavior!

BrickStepper.getIdentity([returnCallback][, errorCallback])¶

Callback Parameters:

uid – Type: string, Length: up to 8 connectedUid – Type: string, Length: up to 8 position – Type: char, Range: ['0' to '8'] hardwareVersion – Type: [int, ...], Length: 3 0: major – Type: int, Range: [0 to 255] 1: minor – Type: int, Range: [0 to 255] 2: revision – Type: int, Range: [0 to 255] firmwareVersion – Type: [int, ...], Length: 3 0: major – Type: int, Range: [0 to 255] 1: minor – Type: int, Range: [0 to 255] 2: revision – Type: int, Range: [0 to 255] deviceIdentifier – Type: int, Range: [0 to 216 - 1]

Returns:

undefined

Returns the UID, the UID where the Brick is connected to, the position, the hardware and firmware version as well as the device identifier.

The position is the position in the stack from '0' (bottom) to '8' (top).

The device identifier numbers can be found here. There is also a constant for the device identifier of this Brick.

Callback Configuration Functions¶

BrickStepper.on(callback_id, function[, errorCallback])¶

Parameters:	callback_id – Type: int function – Type: function
Returns:	undefined

Registers the given function with the given callback_id.

The available callback IDs with corresponding function signatures are listed below.

BrickStepper.setMinimumVoltage(voltage[, returnCallback][, errorCallback])¶

Parameters:	voltage – Type: int, Unit: 1 mV, Range: [0 to 216 - 1], Default: 8000
Callback Parameters:	undefined
Returns:	undefined

Sets the minimum voltage, below which the CALLBACK_UNDER_VOLTAGE callback is triggered. The minimum possible value that works with the Stepper Brick is 8V. You can use this function to detect the discharge of a battery that is used to drive the stepper motor. If you have a fixed power supply, you likely do not need this functionality.

BrickStepper.getMinimumVoltage([returnCallback][, errorCallback])¶

Callback Parameters:	voltage – Type: int, Unit: 1 mV, Range: [0 to 216 - 1], Default: 8000
Returns:	undefined

Returns the minimum voltage as set by setMinimumVoltage().

BrickStepper.setAllDataPeriod(period[, returnCallback][, errorCallback])¶

Parameters:	period – Type: int, Unit: 1 ms, Range: [0 to 232 - 1], Default: 0
Callback Parameters:	undefined
Returns:	undefined

Sets the period with which the CALLBACK_ALL_DATA callback is triggered periodically. A value of 0 turns the callback off.

BrickStepper.getAllDataPeriod([returnCallback][, errorCallback])¶

Callback Parameters:	period – Type: int, Unit: 1 ms, Range: [0 to 232 - 1], Default: 0
Returns:	undefined

Returns the period as set by setAllDataPeriod().

Callbacks¶

Callbacks can be registered to receive time critical or recurring data from the device. The registration is done with the on() function of the device object. The first parameter is the callback ID and the second parameter the callback function:

stepper.on(BrickStepper.CALLBACK_EXAMPLE,
    function (param) {
        console.log(param);
    }
);

The available constants with inherent number and type of parameters are described below.

BrickStepper.CALLBACK_UNDER_VOLTAGE¶

Callback Parameters:	voltage – Type: int, Unit: 1 mV, Range: [0 to 216 - 1]

This callback is triggered when the input voltage drops below the value set by setMinimumVoltage(). The parameter is the current voltage.

BrickStepper.CALLBACK_POSITION_REACHED¶

Callback Parameters:	position – Type: int, Range: [-231 to 231 - 1]

This callback is triggered when a position set by setSteps() or setTargetPosition() is reached.

Note

Since we can't get any feedback from the stepper motor, this only works if the acceleration (see setSpeedRamping()) is set smaller or equal to the maximum acceleration of the motor. Otherwise the motor will lag behind the control value and the callback will be triggered too early.

BrickStepper.CALLBACK_ALL_DATA¶

Callback Parameters:	currentVelocity – Type: int, Unit: 1 1/s, Range: [0 to 216 - 1] currentPosition – Type: int, Range: [-231 to 231 - 1] remainingSteps – Type: int, Range: [-231 to 231 - 1] stackVoltage – Type: int, Unit: 1 mV, Range: [0 to 216 - 1] externalVoltage – Type: int, Unit: 1 mV, Range: [0 to 216 - 1] currentConsumption – Type: int, Unit: 1 mA, Range: [0 to 216 - 1]

This callback is triggered periodically with the period that is set by setAllDataPeriod(). The parameters are: the current velocity, the current position, the remaining steps, the stack voltage, the external voltage and the current consumption of the stepper motor.

BrickStepper.CALLBACK_NEW_STATE¶

Callback Parameters:	stateNew – Type: int, Range: See constants statePrevious – Type: int, Range: See constants

This callback is triggered whenever the Stepper Brick enters a new state. It returns the new state as well as the previous state.

The following constants are available for this function:

For state_new:

• BrickStepper.STATE_STOP = 1
• BrickStepper.STATE_ACCELERATION = 2
• BrickStepper.STATE_RUN = 3
• BrickStepper.STATE_DEACCELERATION = 4
• BrickStepper.STATE_DIRECTION_CHANGE_TO_FORWARD = 5
• BrickStepper.STATE_DIRECTION_CHANGE_TO_BACKWARD = 6

For state_previous:

• BrickStepper.STATE_STOP = 1
• BrickStepper.STATE_ACCELERATION = 2
• BrickStepper.STATE_RUN = 3
• BrickStepper.STATE_DEACCELERATION = 4
• BrickStepper.STATE_DIRECTION_CHANGE_TO_FORWARD = 5
• BrickStepper.STATE_DIRECTION_CHANGE_TO_BACKWARD = 6

Virtual Functions¶

Virtual functions don't communicate with the device itself, but operate only on the API bindings device object. They can be called without the corresponding IP Connection object being connected.

BrickStepper.getAPIVersion()¶

Returns:	apiVersion – Type: [int, ...], Length: 3 0: major – Type: int, Range: [0 to 255] 1: minor – Type: int, Range: [0 to 255] 2: revision – Type: int, Range: [0 to 255]

Returns the version of the API definition implemented by this API bindings. This is neither the release version of this API bindings nor does it tell you anything about the represented Brick or Bricklet.

BrickStepper.getResponseExpected(functionId[, errorCallback])¶

Parameters:	functionId – Type: int, Range: See constants
Returns:	responseExpected – Type: boolean

Returns the response expected flag for the function specified by the function ID parameter. It is true if the function is expected to send a response, false otherwise.

For getter functions this is enabled by default and cannot be disabled, because those functions will always send a response. For callback configuration functions it is enabled by default too, but can be disabled by setResponseExpected(). For setter functions it is disabled by default and can be enabled.

Enabling the response expected flag for a setter function allows to detect timeouts and other error conditions calls of this setter as well. The device will then send a response for this purpose. If this flag is disabled for a setter function then no response is sent and errors are silently ignored, because they cannot be detected.

The following constants are available for this function:

For function_id:

• BrickStepper.FUNCTION_SET_MAX_VELOCITY = 1
• BrickStepper.FUNCTION_SET_SPEED_RAMPING = 4
• BrickStepper.FUNCTION_FULL_BRAKE = 6
• BrickStepper.FUNCTION_SET_CURRENT_POSITION = 7
• BrickStepper.FUNCTION_SET_TARGET_POSITION = 9
• BrickStepper.FUNCTION_SET_STEPS = 11
• BrickStepper.FUNCTION_SET_STEP_MODE = 14
• BrickStepper.FUNCTION_DRIVE_FORWARD = 16
• BrickStepper.FUNCTION_DRIVE_BACKWARD = 17
• BrickStepper.FUNCTION_STOP = 18
• BrickStepper.FUNCTION_SET_MOTOR_CURRENT = 22
• BrickStepper.FUNCTION_ENABLE = 24
• BrickStepper.FUNCTION_DISABLE = 25
• BrickStepper.FUNCTION_SET_DECAY = 27
• BrickStepper.FUNCTION_SET_MINIMUM_VOLTAGE = 29
• BrickStepper.FUNCTION_SET_SYNC_RECT = 33
• BrickStepper.FUNCTION_SET_TIME_BASE = 35
• BrickStepper.FUNCTION_SET_ALL_DATA_PERIOD = 38
• BrickStepper.FUNCTION_SET_SPITFP_BAUDRATE_CONFIG = 231
• BrickStepper.FUNCTION_SET_SPITFP_BAUDRATE = 234
• BrickStepper.FUNCTION_ENABLE_STATUS_LED = 238
• BrickStepper.FUNCTION_DISABLE_STATUS_LED = 239
• BrickStepper.FUNCTION_RESET = 243
• BrickStepper.FUNCTION_WRITE_BRICKLET_PLUGIN = 246

BrickStepper.setResponseExpected(functionId, responseExpected[, errorCallback])¶

Parameters:	functionId – Type: int, Range: See constants responseExpected – Type: boolean
Returns:	undefined

Changes the response expected flag of the function specified by the function ID parameter. This flag can only be changed for setter (default value: false) and callback configuration functions (default value: true). For getter functions it is always enabled.

Enabling the response expected flag for a setter function allows to detect timeouts and other error conditions calls of this setter as well. The device will then send a response for this purpose. If this flag is disabled for a setter function then no response is sent and errors are silently ignored, because they cannot be detected.

The following constants are available for this function:

For function_id:

• BrickStepper.FUNCTION_SET_MAX_VELOCITY = 1
• BrickStepper.FUNCTION_SET_SPEED_RAMPING = 4
• BrickStepper.FUNCTION_FULL_BRAKE = 6
• BrickStepper.FUNCTION_SET_CURRENT_POSITION = 7
• BrickStepper.FUNCTION_SET_TARGET_POSITION = 9
• BrickStepper.FUNCTION_SET_STEPS = 11
• BrickStepper.FUNCTION_SET_STEP_MODE = 14
• BrickStepper.FUNCTION_DRIVE_FORWARD = 16
• BrickStepper.FUNCTION_DRIVE_BACKWARD = 17
• BrickStepper.FUNCTION_STOP = 18
• BrickStepper.FUNCTION_SET_MOTOR_CURRENT = 22
• BrickStepper.FUNCTION_ENABLE = 24
• BrickStepper.FUNCTION_DISABLE = 25
• BrickStepper.FUNCTION_SET_DECAY = 27
• BrickStepper.FUNCTION_SET_MINIMUM_VOLTAGE = 29
• BrickStepper.FUNCTION_SET_SYNC_RECT = 33
• BrickStepper.FUNCTION_SET_TIME_BASE = 35
• BrickStepper.FUNCTION_SET_ALL_DATA_PERIOD = 38
• BrickStepper.FUNCTION_SET_SPITFP_BAUDRATE_CONFIG = 231
• BrickStepper.FUNCTION_SET_SPITFP_BAUDRATE = 234
• BrickStepper.FUNCTION_ENABLE_STATUS_LED = 238
• BrickStepper.FUNCTION_DISABLE_STATUS_LED = 239
• BrickStepper.FUNCTION_RESET = 243
• BrickStepper.FUNCTION_WRITE_BRICKLET_PLUGIN = 246

BrickStepper.setResponseExpectedAll(responseExpected)¶

Parameters:	responseExpected – Type: boolean
Returns:	undefined

Changes the response expected flag for all setter and callback configuration functions of this device at once.

Internal Functions¶

Internal functions are used for maintenance tasks such as flashing a new firmware of changing the UID of a Bricklet. These task should be performed using Brick Viewer instead of using the internal functions directly.

BrickStepper.getProtocol1BrickletName(port[, returnCallback][, errorCallback])¶

Parameters:	port – Type: char, Range: ['a' to 'b']
Callback Parameters:	protocolVersion – Type: int, Range: [0 to 255] firmwareVersion – Type: [int, ...], Length: 3 0: major – Type: int, Range: [0 to 255] 1: minor – Type: int, Range: [0 to 255] 2: revision – Type: int, Range: [0 to 255] name – Type: string, Length: up to 40
Returns:	undefined

Returns the firmware and protocol version and the name of the Bricklet for a given port.

This functions sole purpose is to allow automatic flashing of v1.x.y Bricklet plugins.

BrickStepper.writeBrickletPlugin(port, offset, chunk[, returnCallback][, errorCallback])¶

Parameters:	port – Type: char, Range: ['a' to 'b'] offset – Type: int, Range: [0 to 255] chunk – Type: [int, ...], Length: 32, Range: [0 to 255]
Callback Parameters:	undefined
Returns:	undefined

Writes 32 bytes of firmware to the bricklet attached at the given port. The bytes are written to the position offset * 32.

This function is used by Brick Viewer during flashing. It should not be necessary to call it in a normal user program.

BrickStepper.readBrickletPlugin(port, offset[, returnCallback][, errorCallback])¶

Parameters:	port – Type: char, Range: ['a' to 'b'] offset – Type: int, Range: [0 to 255]
Callback Parameters:	chunk – Type: [int, ...], Length: 32, Range: [0 to 255]
Returns:	undefined

Reads 32 bytes of firmware from the bricklet attached at the given port. The bytes are read starting at the position offset * 32.

This function is used by Brick Viewer during flashing. It should not be necessary to call it in a normal user program.

Constants¶

BrickStepper.DEVICE_IDENTIFIER¶

This constant is used to identify a Stepper Brick.

The getIdentity() function and the IPConnection.CALLBACK_ENUMERATE callback of the IP Connection have a device_identifier parameter to specify the Brick's or Bricklet's type.

BrickStepper.DEVICE_DISPLAY_NAME¶

This constant represents the human readable name of a Stepper Brick.