Shell - Temperature IR Bricklet 2.0

This is the description of the Shell API bindings for the Temperature IR Bricklet 2.0. General information and technical specifications for the Temperature IR Bricklet 2.0 are summarized in its hardware description.

An installation guide for the Shell API bindings is part of their general description.

Examples

The example code below is Public Domain (CC0 1.0).

Simple

Download (example-simple.sh)

 1
 2
 3
 4
 5
 6
 7
 8
 9
10
#!/bin/sh
# Connects to localhost:4223 by default, use --host and --port to change this

uid=XYZ # Change XYZ to the UID of your Temperature IR Bricklet 2.0

# Get current ambient temperature
tinkerforge call temperature-ir-v2-bricklet $uid get-ambient-temperature

# Get current object temperature
tinkerforge call temperature-ir-v2-bricklet $uid get-object-temperature

Callback

Download (example-callback.sh)

 1
 2
 3
 4
 5
 6
 7
 8
 9
10
11
12
13
14
#!/bin/sh
# Connects to localhost:4223 by default, use --host and --port to change this

uid=XYZ # Change XYZ to the UID of your Temperature IR Bricklet 2.0

# Handle incoming object temperature callbacks
tinkerforge dispatch temperature-ir-v2-bricklet $uid object-temperature &

# Set period for object temperature callback to 1s (1000ms) without a threshold
tinkerforge call temperature-ir-v2-bricklet $uid set-object-temperature-callback-configuration 1000 false threshold-option-off 0 0

echo "Press key to exit"; read dummy

kill -- -$$ # Stop callback dispatch in background

Water Boiling

Download (example-water-boiling.sh)

 1
 2
 3
 4
 5
 6
 7
 8
 9
10
11
12
13
14
15
16
17
18
19
#!/bin/sh
# Connects to localhost:4223 by default, use --host and --port to change this

uid=XYZ # Change XYZ to the UID of your Temperature IR Bricklet 2.0

# Set emissivity to 0.98 (emissivity of water, 65535 * 0.98 = 64224.299)
tinkerforge call temperature-ir-v2-bricklet $uid set-emissivity 64224

# Handle incoming object temperature reached callbacks
tinkerforge dispatch temperature-ir-v2-bricklet $uid object-temperature\
 --execute "echo Object Temperature: {temperature}/10 °C. The water is boiling!" &

# Configure threshold for object temperature "greater than 100 °C"
# with a debounce period of 10s (10000ms)
tinkerforge call temperature-ir-v2-bricklet $uid set-object-temperature-callback-configuration 10000 false threshold-option-greater 1000 0

echo "Press key to exit"; read dummy

kill -- -$$ # Stop callback dispatch in background

API

Possible exit codes for all tinkerforge commands are:

  • 1: interrupted (ctrl+c)
  • 2: syntax error
  • 21: Python 2.5 or newer is required
  • 22: Python argparse module is missing
  • 23: socket error
  • 24: other exception
  • 25: invalid placeholder in format string
  • 26: authentication error
  • 201: timeout occurred
  • 209: invalid argument value
  • 210: function is not supported
  • 211: unknown error

Command Structure

The common options of the call and dispatch commands are documented here. The specific command structure is shown below.

tinkerforge call temperature-ir-v2-bricklet [<option>..] <uid> <function> [<argument>..]
Parameters:
  • <uid> -- string
  • <function> -- string

The call command is used to call a function of the Temperature IR Bricklet 2.0. It can take several options:

  • --help shows help for the specific call command and exits
  • --list-functions shows a list of known functions of the Temperature IR Bricklet 2.0 and exits
tinkerforge dispatch temperature-ir-v2-bricklet [<option>..] <uid> <callback>
Parameters:
  • <uid> -- string
  • <callback> -- string

The dispatch command is used to dispatch a callback of the Temperature IR Bricklet 2.0. It can take several options:

  • --help shows help for the specific dispatch command and exits
  • --list-callbacks shows a list of known callbacks of the Temperature IR Bricklet 2.0 and exits
tinkerforge call temperature-ir-v2-bricklet <uid> <function> [<option>..] [<argument>..]
Parameters:
  • <uid> -- string
  • <function> -- string

The <function> to be called can take different options depending of its kind. All functions can take the following options:

  • --help shows help for the specific function and exits

Getter functions can take the following options:

  • --execute <command> shell command line to execute for each incoming response (see section about output formatting for details)

Setter functions can take the following options:

  • --expect-response requests response and waits for it

The --expect-response option for setter functions allows to detect timeouts and other error conditions calls of setters as well. The device will then send a response for this purpose. If this option is not given for a setter function then no response is send and errors are silently ignored, because they cannot be detected.

tinkerforge dispatch temperature-ir-v2-bricklet <uid> <callback> [<option>..]
Parameters:
  • <uid> -- string
  • <callback> -- string

The <callback> to be dispatched can take several options:

  • --help shows help for the specific callback and exits
  • --execute <command> shell command line to execute for each incoming response (see section about output formatting for details)

Basic Functions

tinkerforge call temperature-ir-v2-bricklet <uid> get-ambient-temperature
Output:
  • temperature -- int

Returns the ambient temperature of the sensor. The value has a range of -400 to 1250 and is given in °C/10, e.g. a value of 423 means that an ambient temperature of 42.3 °C is measured.

If you want to get the ambient temperature periodically, it is recommended to use the ambient-temperature callback and set the period with set-ambient-temperature-callback-configuration.

If you want to get the value periodically, it is recommended to use the ambient-temperature callback. You can set the callback configuration with set-ambient-temperature-callback-configuration.

tinkerforge call temperature-ir-v2-bricklet <uid> get-object-temperature
Output:
  • temperature -- int

Returns the object temperature of the sensor, i.e. the temperature of the surface of the object the sensor is aimed at. The value has a range of -700 to 3800 and is given in °C/10, e.g. a value of 3001 means that a temperature of 300.1 °C is measured on the surface of the object.

The temperature of different materials is dependent on their emissivity. The emissivity of the material can be set with set-emissivity.

If you want to get the object temperature periodically, it is recommended to use the object-temperature callback and set the period with set-object-temperature-callback-configuration.

If you want to get the value periodically, it is recommended to use the object-temperature callback. You can set the callback configuration with set-object-temperature-callback-configuration.

Advanced Functions

tinkerforge call temperature-ir-v2-bricklet <uid> set-emissivity <emissivity>
Parameters:
  • <emissivity> -- int
Output:

no output

Sets the emissivity that is used to calculate the surface temperature as returned by get-object-temperature.

The emissivity is usually given as a value between 0.0 and 1.0. A list of emissivities of different materials can be found here.

The parameter of set-emissivity has to be given with a factor of 65535 (16-bit). For example: An emissivity of 0.1 can be set with the value 6553, an emissivity of 0.5 with the value 32767 and so on.

Note

If you need a precise measurement for the object temperature, it is absolutely crucial that you also provide a precise emissivity.

The default emissivity is 1.0 (value of 65535) and the minimum emissivity the sensor can handle is 0.1 (value of 6553).

tinkerforge call temperature-ir-v2-bricklet <uid> get-emissivity
Output:
  • emissivity -- int

Returns the emissivity as set by set-emissivity.

tinkerforge call temperature-ir-v2-bricklet <uid> get-spitfp-error-count
Output:
  • error-count-ack-checksum -- int
  • error-count-message-checksum -- int
  • error-count-frame -- int
  • error-count-overflow -- int

Returns the error count for the communication between Brick and Bricklet.

The errors are divided into

  • ACK checksum errors,
  • message checksum errors,
  • framing errors and
  • overflow errors.

The errors counts are for errors that occur on the Bricklet side. All Bricks have a similar function that returns the errors on the Brick side.

tinkerforge call temperature-ir-v2-bricklet <uid> set-bootloader-mode <mode>
Parameters:
  • <mode> -- int (has symbols)
Output:
  • status -- int (has symbols)

Sets the bootloader mode and returns the status after the requested mode change was instigated.

You can change from bootloader mode to firmware mode and vice versa. A change from bootloader mode to firmware mode will only take place if the entry function, device identifier and CRC are present and correct.

This function is used by Brick Viewer during flashing. It should not be necessary to call it in a normal user program.

The following symbols are available for this function:

  • bootloader-mode-bootloader = 0, for <mode>
  • bootloader-mode-firmware = 1, for <mode>
  • bootloader-mode-bootloader-wait-for-reboot = 2, for <mode>
  • bootloader-mode-firmware-wait-for-reboot = 3, for <mode>
  • bootloader-mode-firmware-wait-for-erase-and-reboot = 4, for <mode>
  • bootloader-status-ok = 0, for status
  • bootloader-status-invalid-mode = 1, for status
  • bootloader-status-no-change = 2, for status
  • bootloader-status-entry-function-not-present = 3, for status
  • bootloader-status-device-identifier-incorrect = 4, for status
  • bootloader-status-crc-mismatch = 5, for status
tinkerforge call temperature-ir-v2-bricklet <uid> get-bootloader-mode
Output:
  • mode -- int (has symbols)

Returns the current bootloader mode, see set-bootloader-mode.

The following symbols are available for this function:

  • bootloader-mode-bootloader = 0, for mode
  • bootloader-mode-firmware = 1, for mode
  • bootloader-mode-bootloader-wait-for-reboot = 2, for mode
  • bootloader-mode-firmware-wait-for-reboot = 3, for mode
  • bootloader-mode-firmware-wait-for-erase-and-reboot = 4, for mode
tinkerforge call temperature-ir-v2-bricklet <uid> set-write-firmware-pointer <pointer>
Parameters:
  • <pointer> -- int
Output:

no output

Sets the firmware pointer for write-firmware. The pointer has to be increased by chunks of size 64. The data is written to flash every 4 chunks (which equals to one page of size 256).

This function is used by Brick Viewer during flashing. It should not be necessary to call it in a normal user program.

tinkerforge call temperature-ir-v2-bricklet <uid> write-firmware <data>
Parameters:
  • <data> -- int,int,..61x..,int
Output:
  • status -- int

Writes 64 Bytes of firmware at the position as written by set-write-firmware-pointer before. The firmware is written to flash every 4 chunks.

You can only write firmware in bootloader mode.

This function is used by Brick Viewer during flashing. It should not be necessary to call it in a normal user program.

tinkerforge call temperature-ir-v2-bricklet <uid> set-status-led-config <config>
Parameters:
  • <config> -- int (has symbols)
Output:

no output

Sets the status LED configuration. By default the LED shows communication traffic between Brick and Bricklet, it flickers once for every 10 received data packets.

You can also turn the LED permanently on/off or show a heartbeat.

If the Bricklet is in bootloader mode, the LED is will show heartbeat by default.

The following symbols are available for this function:

  • status-led-config-off = 0, for <config>
  • status-led-config-on = 1, for <config>
  • status-led-config-show-heartbeat = 2, for <config>
  • status-led-config-show-status = 3, for <config>
tinkerforge call temperature-ir-v2-bricklet <uid> get-status-led-config
Output:
  • config -- int (has symbols)

Returns the configuration as set by set-status-led-config

The following symbols are available for this function:

  • status-led-config-off = 0, for config
  • status-led-config-on = 1, for config
  • status-led-config-show-heartbeat = 2, for config
  • status-led-config-show-status = 3, for config
tinkerforge call temperature-ir-v2-bricklet <uid> get-chip-temperature
Output:
  • temperature -- int

Returns the temperature in °C as measured inside the microcontroller. The value returned is not the ambient temperature!

The temperature is only proportional to the real temperature and it has bad accuracy. Practically it is only useful as an indicator for temperature changes.

tinkerforge call temperature-ir-v2-bricklet <uid> reset
Output:no output

Calling this function will reset the Bricklet. All configurations will be lost.

After a reset you have to create new device objects, calling functions on the existing ones will result in undefined behavior!

tinkerforge call temperature-ir-v2-bricklet <uid> write-uid <uid>
Parameters:
  • <uid> -- int
Output:

no output

Writes a new UID into flash. If you want to set a new UID you have to decode the Base58 encoded UID string into an integer first.

We recommend that you use Brick Viewer to change the UID.

tinkerforge call temperature-ir-v2-bricklet <uid> read-uid
Output:
  • uid -- int

Returns the current UID as an integer. Encode as Base58 to get the usual string version.

tinkerforge call temperature-ir-v2-bricklet <uid> get-identity
Output:
  • uid -- string
  • connected-uid -- string
  • position -- char
  • hardware-version -- int,int,int
  • firmware-version -- int,int,int
  • device-identifier -- int (has symbols)

Returns the UID, the UID where the Bricklet is connected to, the position, the hardware and firmware version as well as the device identifier.

The position can be 'a', 'b', 'c' or 'd'.

The device identifier numbers can be found here

Callback Configuration Functions

tinkerforge call temperature-ir-v2-bricklet <uid> set-ambient-temperature-callback-configuration <period> <value-has-to-change> <option> <min> <max>
Parameters:
  • <period> -- int
  • <value-has-to-change> -- bool
  • <option> -- char (has symbols)
  • <min> -- int
  • <max> -- int
Output:

no output

The period in ms is the period with which the ambient-temperature callback is triggered periodically. A value of 0 turns the callback off.

If the value has to change-parameter is set to true, the callback is only triggered after the value has changed. If the value didn't change within the period, the callback is triggered immediately on change.

If it is set to false, the callback is continuously triggered with the period, independent of the value.

It is furthermore possible to constrain the callback with thresholds.

The option-parameter together with min/max sets a threshold for the ambient-temperature callback.

The following options are possible:

Option Description
'x' Threshold is turned off
'o' Threshold is triggered when the value is outside the min and max values
'i' Threshold is triggered when the value is inside or equal to the min and max values
'<' Threshold is triggered when the value is smaller than the min value (max is ignored)
'>' Threshold is triggered when the value is greater than the min value (max is ignored)

If the option is set to 'x' (threshold turned off) the callback is triggered with the fixed period.

The default value is (0, false, 'x', 0, 0).

The following symbols are available for this function:

  • threshold-option-off = x, for <option>
  • threshold-option-outside = o, for <option>
  • threshold-option-inside = i, for <option>
  • threshold-option-smaller = <, for <option>
  • threshold-option-greater = >, for <option>
tinkerforge call temperature-ir-v2-bricklet <uid> get-ambient-temperature-callback-configuration
Output:
  • period -- int
  • value-has-to-change -- bool
  • option -- char (has symbols)
  • min -- int
  • max -- int

Returns the callback configuration as set by set-ambient-temperature-callback-configuration.

The following symbols are available for this function:

  • threshold-option-off = x, for option
  • threshold-option-outside = o, for option
  • threshold-option-inside = i, for option
  • threshold-option-smaller = <, for option
  • threshold-option-greater = >, for option
tinkerforge call temperature-ir-v2-bricklet <uid> set-object-temperature-callback-configuration <period> <value-has-to-change> <option> <min> <max>
Parameters:
  • <period> -- int
  • <value-has-to-change> -- bool
  • <option> -- char (has symbols)
  • <min> -- int
  • <max> -- int
Output:

no output

The period in ms is the period with which the object-temperature callback is triggered periodically. A value of 0 turns the callback off.

If the value has to change-parameter is set to true, the callback is only triggered after the value has changed. If the value didn't change within the period, the callback is triggered immediately on change.

If it is set to false, the callback is continuously triggered with the period, independent of the value.

It is furthermore possible to constrain the callback with thresholds.

The option-parameter together with min/max sets a threshold for the object-temperature callback.

The following options are possible:

Option Description
'x' Threshold is turned off
'o' Threshold is triggered when the value is outside the min and max values
'i' Threshold is triggered when the value is inside or equal to the min and max values
'<' Threshold is triggered when the value is smaller than the min value (max is ignored)
'>' Threshold is triggered when the value is greater than the min value (max is ignored)

If the option is set to 'x' (threshold turned off) the callback is triggered with the fixed period.

The default value is (0, false, 'x', 0, 0).

The following symbols are available for this function:

  • threshold-option-off = x, for <option>
  • threshold-option-outside = o, for <option>
  • threshold-option-inside = i, for <option>
  • threshold-option-smaller = <, for <option>
  • threshold-option-greater = >, for <option>
tinkerforge call temperature-ir-v2-bricklet <uid> get-object-temperature-callback-configuration
Output:
  • period -- int
  • value-has-to-change -- bool
  • option -- char (has symbols)
  • min -- int
  • max -- int

Returns the callback configuration as set by set-object-temperature-callback-configuration.

The following symbols are available for this function:

  • threshold-option-off = x, for option
  • threshold-option-outside = o, for option
  • threshold-option-inside = i, for option
  • threshold-option-smaller = <, for option
  • threshold-option-greater = >, for option

Callbacks

Callbacks can be used to receive time critical or recurring data from the device:

tinkerforge dispatch temperature-ir-v2-bricklet <uid> example

The available callbacks are described below.

Note

Using callbacks for recurring events is always preferred compared to using getters. It will use less USB bandwidth and the latency will be a lot better, since there is no round trip time.

tinkerforge dispatch temperature-ir-v2-bricklet <uid> ambient-temperature
Output:
  • temperature -- int

This callback is triggered periodically according to the configuration set by set-ambient-temperature-callback-configuration.

The parameter is the same as get-ambient-temperature.

tinkerforge dispatch temperature-ir-v2-bricklet <uid> object-temperature
Output:
  • temperature -- int

This callback is triggered periodically according to the configuration set by set-object-temperature-callback-configuration.

The parameter is the same as get-object-temperature.